In a water damage event, it is vital to quickly remove the water and wash your own property. This way, you may reduce additional damage to your house’s structure and contents, such as floors, furniture, ceiling, and drywall (gypsum board). Based on the sort of flood and where water has intruded, the drywall must be either entirely or partially replaced. Read below to learn how to fix water damaged drywall.
Items to know before learning how to repair water damaged drywall
If moist drywall is brought on by an overhead flood, the ceiling can collapse. In cases like this, have your house’s structure assessed by a professional restoration company. Visit water damage restoration Downey for more information.
Additionally, if the drywall water damage was caused by sewage backup, consult with certified professionals for repairs. This type of job involves security issues and biohazard cleaning services that are usually beyond the capacity of typical homeowners.
Before repairing water damaged drywall, locate and fix the water supply. Extract the water and dry the area. The longer the water sits, the larger the harm to your drywall will be.
How to repair water damaged drywall
First, clear the area. Remove water-soaked furniture and construction materials. Also, remove wet carpeting and padding, or pull it back to allow the floor to air out.
Take security precautions
When removing drywall, wear respiratory protection as some older drywall joint compound contains asbestos. Furthermore, remove non-affected electric outlets before ripping out wall material. When the sockets have been flooded, remove and discard them.
Eliminate damaged materials
Begin by determining how much drywall to cut away. If the water level was less than two-and-a-half feet, eliminate the wall material to a height of four feet. That helps when reinstalling complete sheets of drywall. If the water level has been higher than two-and-a-half feet, remove the wall material to a height of eight feet or the ceiling junction, whichever is higher.
If you do not know the water level, inspect the drywall. Remove any cracked, crumbling, or sagging drywall. But if it is only moist and also the water supply was sterile (e.g., A burst pipe in your house), you may probably dry it. Based upon the extent of the water damage, you might also need to remove damaged wall studs, cabinets, flooring, and ceilings. Next, it’s time to cut the damaged parts of the drywall.
How to cut drywall
- Mark a straight line along the wall — above the point where the water stopped wicking — using a chalk line.
- Cut along the chalk line one-half or three-quarters of the way throughout the thickness of the drywall. Use a utility knife.
- Loosen and remove the damaged part carefully. To make that easier, knock on a little hole in the broken drywall using a hammer. Use the hole as a handle to pull back the drywall.
- Once you cut and remove the drywall, take out all the insulation (fiberglass, mineral wool, cellulose, wood fiberboard, etc.). Even if it does not seem wet, it probably is. When it’s foam plastic insulation, it is possible to leave it in place and allow it to dry.
Dry the water ruined walls
When the damaged drywall is removed, begin drying the area around and in the wall. Utilize high-efficiency blowers and dehumidifiers and open the windows and doors. Use fans to improve airflow behind walls and then leave them running for at least two days so that the studs and floors can completely dry.
Note: prevent punching holes in walls. This practice doesn’t help the wall dry faster. Plus, it makes it more challenging to repair your own shingles.
Use a chemical sanitizer to prevent mold and bacteria from forming between partitions. Prevent bleach as it doesn’t prevent mold from growing. To remove severe scents, use an ozone machine and leave it running for at least eight hours. Vacate the area while the ozone machine is running.
Now it is time to hang fresh drywall. First, measure the size of the hole that will help you know how much to cut from a new sheet of drywall. Place four shingles clips around the pit and fasten every one using a drywall screw.
Then, insert the drywall pieces and fasten them to drywall clips. Finally, sand the area several times to get a smooth wall surface.
Paint the revived drywall
This is the final step in restoring water damaged shingles. First, ensure the joint compound is completely dry as it might include a lot of moisture. Then, paint the wall with a primer that will help seal the region. After that, paint the whole wall to ensure the color is uniform throughout.
For skilled drywall water damage repair, phone PuroClean!
As you have noticed, the processes of how to fix water damaged drywall are time-consuming and complicated. Everything has to be carried out quickly using the right techniques and tools. Visit disaster restoration Paramount to learn more.
Don’t risk further harm by taking on the task of drywall water damage fix yourself. We use professional equipment, for example, heavy duty air movers, commercial dehumidifiers, moisture meters, and high-volume water extractors, to quickly and efficiently dry and fix your drywall and the surrounding damp locations.
To recap, this is how to repair water damaged drywall:
- Find and fix the water supply that caused the harm.
- Take safety precautions — wear a dust mask, rubber gloves, and turn off the circuit breaker.
- Remove the damaged portions of the drywall. Cut them with a utility knife.
- Further arid the water damaged walls using fans and dehumidifiers.
- Sanitize and deodorize the area to eliminate musty smells and bacteria.
- Replace the cut-out portions of the drywall.
- Paint the restored shingles using mold-resistant paint.
- Call a restoration firm to do these tasks for you fast and efficiently.